澳门新葡亰平台官网

发表论文(SCI收录)
2014-10-31访问次数:

1)      Xu X. Friction studies on the process in circular sawing of granites[J]. Tribology Letters, 1999, 7(4): 221-227.

2)      Xu X. Experimental study on temperatures and energy partition at the diamond–granite interface in grinding[J]. Tribology International, 2001, 34(6): 419-426.

3)      Xu X, Li Y, Malkin S. Forces and energy in circular sawing and grinding of granite[J]. Journal of Manufacturing Science and Engineering, 2001, 123(1): 13-22.

4)      Xu X. Study on the thermal wear of diamond segmented tools in circular sawing of granites[J]. Tribology Letters, 2001, 10(4): 245-250.

5)      Xu X, Malkin S. Comparison of methods to measure grinding temperatures[J]. Journal of Manufacturing science and engineering, 2001, 123(2): 191-195.

6)      Xu X, Yu Y. XPS and SEM characterization of wheel/workpiece interface in grinding of superalloy[J]. Surface and interface analysis, 2002, 33(4): 343-350.

7)      Xu X, Yu Y. Adhesion at abrasive-Ti6Al4V interface with elevated grinding temperatures[J]. Journal of materials science letters, 2002, 21(16): 1293-1295.

8)      Shen J Y, Luo C B, Zeng W M, et al. Ceramics grinding under the condition of constant pressure[J]. Journal of materials processing technology, 2002, 129(1): 176-181.

9)      Xu X P, Yu Y Q, Xu H J. Effect of grinding temperatures on the surface integrity of a nickel-based superalloy[J]. Journal of materials processing technology, 2002, 129(1): 359-363.

10)    Li Y, Huang H, Shen J Y, et al. Cost-effective machining of granite by reducing tribological interactions[J]. Journal of materials processing technology, 2002, 129(1): 389-394.

11)    Xu X P, Li Y, Zeng W Y, et al. Quantitative analysis of the loads acting on the abrasive grits in the diamond sawing of granites[J]. Journal of materials processing technology, 2002, 129(1): 50-55.

12)    Dai Q L, Luo C B, Xu X P, et al. Effects of rare earth and sintering temperature on the transverse rupture strength of Fe-based diamond composites[J]. Journal of materials processing technology, 2002, 129(1): 427-430.

13)    Shen J Y, Zeng W M, Huang H, et al. Thermal aspects in the face grinding of ceramics[J]. Journal of materials processing technology, 2002, 129(1): 212-216.

14)    Huang H, Li Y, Shen J Y, et al. Micro-structure detection of a glossy granite surface machined by the grinding process[J]. Journal of materials processing technology, 2002, 129(1): 403-407.

15)    Xu X P. Measurement of temperatures in grinding of brittle materials using two-color infrared system[J]. Journal of infrared millim waves, 2002,21(2):99-103

16)    u X, Yu Y, Huang H. Mechanisms of abrasive wear in the grinding of titanium (TC4) and nickel (K417) alloys[J]. Wear, 2003, 255(7): 1421-1426.

17)    Xu X, Li Y, Yu Y. Force ratio in the circular sawing of granites with a diamond segmented blade[J]. Journal of Materials Processing Technology, 2003, 139(1): 281-285.

18)    Xu X. Tribological interactions at the wheel–workpiece interface in surface grinding of construction stone[J]. Surface and interface analysis, 2004, 36(8): 1250-1253.

19)    Huang H, Xu X P. Interfacial interactions between diamond disk and granite during vertical spindle grinding[J]. Wear, 2004, 256(6): 623-629.

20)    Xu X, Tie X, Wu H. The effects of a Ti coating on the performance of metal-bonded diamond composites containing rare earth[J]. International Journal of Refractory Metals and Hard Materials, 2007, 25(3): 244-249.

21)    Xu X P, Tie X R, Yu Y Q. The effects of rare earth on the fracture properties of different metal–diamond composites[J]. Journal of materials processing technology, 2007, 187: 421-424.

22)    Xu X, Du C. Friction studies on surface grinding of granite with a vitrified CBN wheel[J]. Surface and Interface Analysis, 2008, 40(34): 863-866.

23)    Chen J, Huang H, Xu X. An experimental study on the grinding of alumina with a monolayer brazed diamond wheel[J]. The International Journal of Advanced Manufacturing Technology, 2009, 41(1-2): 16-23.

24)    Chen J, Xu X. Temperature and energy partition in high-speed grinding of alumina with a brazed diamond wheel[J]. Machining Science and Technology, 2010, 14(4): 440-454.

25)    Chen J, Shen J, Huang H, et al. Grinding characteristics in high speed grinding of engineering ceramics with brazed diamond wheels[J]. Journal of Materials Processing Technology, 2010, 210(6): 899-906.

26)    Zhan Y J, Xu X P. An experimental investigation of temperatures and energy partition in grinding of cemented carbide with a brazed diamond wheel[J]. The International Journal of Advanced Manufacturing Technology, 2012, 61(1-4): 117-125.

27)    Lu J, Li D, Yu D. Study on Electronic Properties of Single-Walled B3C10N3 Nanotubes by First Principle Calculations[J]. Integrated Ferroelectrics, 2012, 135(1): 17-21.

28)    Cui C, Xu X, Huang H, et al. Extraction of the grains topography from grinding wheels[J]. Measurement, 2013, 46(1): 484-490.

29)    Huang G, Xu X. Sawing performance comparison of brazed and sintered diamond wires[J]. Chinese Journal of Mechanical Engineering, 2013, 26(2): 393-399.

30)    Huang H, Huang G, Xu X, et al. An experimental study of machining characteristics and tool wear in the diamond wire sawing of granite[J]. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2013: 0954405413478262.

31)    Cui C, Xu X, Huang H, et al. Extraction of the grains topography from grinding wheels[J]. Measurement, 2013, 46(1): 484-490.

 

XML 地图 | Sitemap 地图